Pay in installments of $5.02 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 28 - Aug 2
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
gas pedal gas pedal Aluminum Accelerator Pedal Assembly (All Spridgets) – BugeyeguysThis add on accessory is a must for every Spridget with a bottom hinging gas pedal. Here's why Original Bugeye accelerator pedals are a terrible design. They plug into a pivoting metal rod and can easily become un plugged while driving, which is an obvious safety hazard. Once the pedal disconnects, Its not difficult to lodge the rubber pedal on the accelerator rod, thus sticking the throttle OPEN! The other challenge with this original design is the
This add-on accessory is a must for every Spridget with a bottom hinging gas pedal. Here's why...
Original Bugeye accelerator pedals are a terrible design. They plug into a pivoting metal rod and can easily become un-plugged while driving, which is an obvious safety hazard. Once the pedal disconnects, It’s not difficult to lodge the rubber pedal on the accelerator rod, thus sticking the throttle OPEN!
The other challenge with this original design is the hinge mount requires two holes in your nice floor pan. Since it is naturally rusting and making holes on its own, it’s never fun to punch more holes if you don’t have to. Those accelerator holes can become yet another source of corrosion.
Since about 1979 I have been driving my Bugeye ‘Gumby” with just metal bar under my foot and no pedal. And on the cars the we ship to customers, we remove the pedal for safety. Even though it doesn’t look pretty, the bar has been our best solution, until now.
We are exited to offer a nice cast aluminum pad you can easily bolt into place, along with a rubber pedal pad to cover it. This is an elegant solution to an old problem. It’s easy to install and makes heel/toe shifting easy. This is an upgrade that is a winner for every early Sprite!
You get the aluminum bolt on pad, hardware to mount it and a rubber pedal pad, which you will need to install on the aluminum pad before installation.
NOTE: The star washers go in between the aluminum pedal ears and the metal accelerator rod-see photos below. These take up the space and allow for a snug fit before you tighten the bolt. Make sure to tighten the bolt so that the pedal is snug. It can float a little, but make sure to tighten the bolt sufficiently to ensure that the pedal can't flop around. Make sure to use the star washers as shown. Tighten the bolt until the star washers bite into the metal accelerator rod, even if it slightly bends the aluminum "ears" of the casting. The ears may bend slightly, but if the bolt is overtightened the ears can snap, so don't overtighten! We are not responsible for broken ears due to over tightening.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.7 ★★★★★
Based on 25 reviews
Sort
Product Reviews
★★★★★ 5
Stable, attractive, and easy to turn into a table with your choice of top
Size: side table leg
The X-shape of the table legs - constructed with solid metal flanges, T-joints, X-joints and 1-inch diameter pipes - provides a strong and sturdy base for a wood top. The legs have adjustable feet pads to prevent scratches and ensure stability. Assembly of the legs is relatively simple (the instructions are clear) but you will need your own tools to attach a top.
The industrial design is especially well suited to rec room or finished basement use. I am adding a 28" diameter raw edge slab of wood from a recently felled tree as the top and it is very attractive. (Photo unavailable because after I made certain it would work I sent the slab out for drying and finishing.)
If you want a custom table and have a particular piece of wood you want to use, these legs are an excellent choice.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 18, 2026
★★★★★ 5
Very nice kit: Beware it is NOT heavy duty plumbing pipe though!
Size: side table leg
I want to give this kit a high rating, but I need to address the "truth in advertising" bit since there may be an important disconnect between what you think you are getting and what actually comes in the box.
Black plumbing used for shelving or table legs is part of an important niche in interior design. I like the industrial loft look myself and have a variety of glass, steel, and masonry elements in my home. This kit fits that look and provides plenty of "strength" for most domestic uses, like shelves or coffee tables. But they are NOT "industrial pipe" or "maximum durability pipe." Note the phrase "cast iron finish feet," which together with the other claims might lead you to think these are cast plumbing fittings. They are NOT!
The feet and flanges feel like electrical conduit fittings, and the pipe sections are likely aluminum. They might be electrical or they might be multi-use, lightweight pipe.
While all this might lead you to think that you're getting a truly retro, heavy-duty pipe kit made of black plumbing pipe, you are not. But, does it matter? Depends. I find the lighter pipe's smooth finish a nice "tone-down" from the rough plumbing look. All together, this kit provides plenty of strength for most furniture and the rustic pipe look, but with a nicer, lighter finish. To me that is a plus--this is a very nice kit and costs less that if you'd pieced it together from real plumbing parts (I priced it out to compare), and looks retro but cleaner. I knew what to expect because while I got this kit free on Vine, I had purchased a nearly identical kit from another seller last year.
So, I'm giving it 5 stars for what it actually is and for the price, JUST BE AWARE THE NARRATIVE IS MISLEADING. Which is unfortunate because just like some people might want the heavier pipe, I'm betting more would be attracted to the look with a cleaner, lighter feel.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 31, 2025
★★★★★ 5
Strong legs, somewhat industrial but trendy also
Size: side table leg
Good legs, some what utilitarian or industrial, they are strong as they are made out of pipe, and assembly is fairly easy once you get the idea of how it goes together. They are roughly 1.5 feet across maybe a bit less adjustable height on each leg, if you have wood floors you may want to put a pad under each leg as they are full metal pipes. Pretty interesting idea and does not cost much.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 31, 2026
★★★★★ 4
Pretty good, take your time and install it well
Size: side table leg
Materials are pretty solid, but once assembled it’s not as sturdy as you would think it should be since the material itself was solid, i say give them a chance, everything out there that’s similar is way over priced
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 4, 2026
★★★★★ 5
Heavy duty legs for table.
Size: side table leg
Perfect legs for a table I am having made. I have an cottonwood slice. It's heavy and needed something substantial.
These are perfect.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 25, 2026